Client Zone Knowledgebase ezybroadband Connect a DrayTek Vigor router to the NBN

Connect a DrayTek Vigor router to the NBN

Print
nbn, router, pppoe 0

This guide connects a DrayTek Vigor router to our NBN service: through the NBN box for fibre, HFC and fibre-to-the-curb, or through the phone socket for fibre-to-the-node or building on Vigor models with a built-in VDSL modem. DrayTek has two styles of menu, so pick the tab that matches your router.

Updated 21 November 2026Applies to DrayTek routers

What you'll need

  • Your NBN username and password, from the welcome email we sent
  • A computer connected to the router by cable or Wi-Fi
  • The router's sign-in details, usually on a label underneath it

Your NBN settings

Connection typePPPoE
UsernameAs supplied, for example yourname@ezynbn.net.au
PasswordAs supplied
IP addressGet it automatically. If your router has a field for a fixed IP address, enter the static IP address we supplied.
DNSAutomatic. If your router needs them entered: 103.5.90.253 and 103.5.91.253
MTU1492
VLANOff, for most businesses. If you use VLANs: VLAN ID 100, priority 0

Set up the DrayTek

  1. Find your WAN settings

    Newer menus (DrayOS 5)

    Go to Configuration >> WAN, open the WAN Connections tab and select Edit on the WAN you're using.

    Classic menus (DrayOS 4)

    Go to WAN >> Internet Access. On models with a modem, the phone-line WAN is WAN1 and the Ethernet WAN is WAN2.

  2. Choose PPPoE and sign in

    Newer menus (DrayOS 5)

    Set IPv4 Connection Type to PPPoE (PPPoE/PPPoA on a phone-line WAN) and enter your Username and Password.

    Classic menus (DrayOS 4)

    Set Access Mode to PPPoE (PPPoE / PPPoA on a phone-line WAN), select Details Page, and enter your Username and Password.

  3. Set the MTU

    Set MTU to 1492, the highest a PPPoE connection allows.

  4. DNS, only if needed (DrayOS 5)

    Set WAN DNS to Manual and enter the two addresses.

  5. Save

    Select Apply (DrayOS 5) or OK (DrayOS 4), and restart the router if it asks.

VLAN

VLAN or no VLAN? If you're not sure, you don't need one: leave VLAN settings off. Use VLAN ID 100 only if your business uses VLANs, or the person who looks after your network asks for it.

No VLAN (most businesses)

Leave the VLAN settings off: on DrayOS 5, the Customer VLAN and Service VLAN toggles; on DrayOS 4, VLAN Tag insertion = Disable (WAN >> General Setup).

Using a VLAN

On DrayOS 5, turn on Customer VLAN and set Tag to 100, Priority 0. On DrayOS 4, go to WAN >> General Setup, open the WAN and set VLAN Tag insertion to Enable, Tag value 100, Priority 0. Leave Service VLAN off.

Still not working?

  • Check the username is the whole address, including @ezynbn.net.au, and retype the password.
  • If you turned on a VLAN, try again with it off (or the other way round).
  • Restart the NBN box and the router, then wait two minutes.
  • Still stuck? Open a ticket with your router's make and model, and a photo of the lights on the NBN box.

What's next

Steps follow DrayTek's Vigor2867 user guide (DrayOS 5, September 2026) and Vigor2866 user guide (DrayOS 4, May 2025).

Was this guide helpful?

Still stuck?

Send us the details and our team will take it from here

Open Ticket